Super Flower Leadex Gold 650W Review

1. Introduction2. Super Flower Leadex Gold 650W (Bundle & Cables)3. Super Flower Leadex Gold 650W (External)4. Super Flower Leadex Gold 650W (Internal)5. Super Flower Leadex Gold 650W (High Res Gallery)6. Testing Methodology & Results7. Closing Thoughts8. View All Pages

Additional technical assistance: Peter McFarland and Jeremy Price.

Correctly testing power supplies is a complex procedure and KitGuru have configured a test bench which can deliver up to a 2,000 watt DC load. Due to public requests we have changed our temperature settings recently – previously we rated with ambient temperatures at 25C, we have increased ambient temperatures by 10c (to 35c) in our environment to greater reflect warmer internal chassis conditions.

We use combinations of the following hardware:
• SunMoon SM-268
• CSI3710A Programmable DC load (+3.3V and +5V outputs)
• CSI3711A Programmable DC load (+12V1, +12V2, +12V3, and +12V4)
• Extech Power Analyzer
• Extech MultiMaster MM570 digital multimeter
• SkyTronic DSL 2 Digital Sound Level Meter (6-130dBa)
• Digital oscilloscope (20M S/s with 12 Bit ADC)
• Variable Autotransformer, 1.4 KVA

DC Output Load Regulation
Combined DC Load	+3.3V		+5V		+12V		+5VSB		-12V
	A	V	A	V	A	V	A	V	A	V
152W	2.08	3.32	2.04	5.05	10.14	12.24	0.50	5.02	0.20	-12.06
270W	3.05	3.32	3.07	5.04	19.16	12.22	0.50	5.01	0.30	-12.08
400W	4.05	3.32	5.05	5.02	29.18	12.18	1.00	5.01	0.30	-12.09
523W	6.08	3.31	7.06	5.02	38.31	12.14	1.50	5.01	0.30	-12.10
650W	8.00	3.31	9.02	5.01	48.00	12.10	2.50	5.00	0.30	-12.11

Load regulation is good with all rails holding within 1 percent deviation.

Super Flower Leadex Gold 650W	Maximum Load
	715W

The power supply would shut down at 715W, gracefully. The protection circuitry worked well.

Next we want to try Cross Loading. This basically means loads which are not balanced. If a PC for instance needs 500W on the +12V outputs but something like 30W via the combined 3.3V and +5V outputs then the voltage regulation can fluctuate badly.

Cross Load Testing	+3.3V		+5V		+12V		-12V		+5VSB
	A	V	A	V	A	V	A	V	A	V
590W	1.0	3.32	1.0	5.05	48.0	12.09	0.2	-12.04	0.50	5.01
145W	12.0	3.31	15.0	5.00	2.0	12.22	0.2	-12.03	0.50	5.00

Cross load results are also strong, with all the rails holding well, without much deviation.

We then used an oscilloscope to measure AC ripple and noise present on the DC outputs. We set the oscilloscope time base to check for AC ripple at both high and low ends of the spectrum. ATX12V V2.2 specification for DC output ripple and noise is defined in the ATX 12V power supply design guide.

ATX12V Ver 2.2 Noise/Ripple Tolerance
Output	Ripple (mV p-p)
+3.3V	50
+5V	50
+12V1	120
+12V2	120
-12V	120
+5VSB	50

Obviously when measuring AC noise and ripple on the DC outputs the cleaner (less recorded) means we have a better end result. We measured this AC signal amplitude to see how closely the unit complied with the ATX standard.

AC Ripple (mV p-p)
DC Load	+3.3V	+5V	+12V	5VSB
152W	10	10	10	5
270W	10	10	10	5
400W	15	10	10	5
523W	15	10	15	10
650W	15	10	15	10

Ripple suppression is excellent, with all rails holding between 10mV and 15mV at full load.

Efficiency (%)
152W	90.23
270W	92.18
400W	91.83
523W	91.14
650W	90.55

Efficiency is strong, peaking at just over 92 percent around 50 percent load. This drops to just over 90 percent efficiency at full load.

We take the issue of noise very seriously at KitGuru and this is why we have built a special home brew system as a reference point when we test noise levels of various components. Why do this? Well this means we can eliminate secondary noise pollution in the test room and concentrate on components we are testing. It also brings us slightly closer to industry standards, such as DIN 45635.

Today to test the Power Supply we have taken it into our acoustics room environment and have set our SkyTronic DSL 2 Digital Sound Level Meter (6-130dBa) one meter away from the unit. We have no other fans running so we can effectively measure just the noise from the unit itself.

As this can be a little confusing for people, here are various dBa ratings in with real world situations to help describe the various levels.

KitGuru noise guide
10dBA – Normal Breathing/Rustling Leaves
20-25dBA – Whisper
30dBA – High Quality Computer fan
40dBA – A Bubbling Brook, or a Refrigerator
50dBA – Normal Conversation
60dBA – Laughter
70dBA – Vacuum Cleaner or Hairdryer
80dBA – City Traffic or a Garbage Disposal
90dBA – Motorcycle or Lawnmower
100dBA – MP3 Player at maximum output
110dBA – Orchestra
120dBA – Front row rock concert/Jet Engine
130dBA – Threshold of Pain
140dBA – Military Jet takeoff/Gunshot (close range)
160dBA – Instant Perforation of eardrum

Noise (dBA)
152W	28.0
270W	28.8
400W	31.3
523W	34.2
650W	36.1

The fan doesn't spin much until 500 watts is demanded. At 550W the fan is audible and at 650 watts the noise is clearly noticeable, rating at just over 36 dBa.

Temperature (c)
	Intake	Exhaust
152W	36	41
270W	39	48
400W	42	54
523W	43	57
650W	45	61

At full load exhaust temperature was hitting 61c.

Maximum load	Efficiency
715W	89.6

Pushing the power supply above its rated limits generates an ultimate efficiency level of around 89.6%. This is not a viable ‘real world’ situation, but it is interesting nonetheless.

Become a Patron!