Silverstone Strider Plus 1000W Review (SST-ST1000-P)

1. Introduction2. Silverstone Strider Plus 1000W (Bundle/Cabling)3. Silverstone Stider Plus 1000W (External)4. Silverstone Strider Plus 1000W (Internal)5. Testing Methodology and Results6. Closing Thoughts7. View All Pages

Additional technical assistance: Peter McFarland and Jeremy Price.

Correctly testing power supplies is a complex procedure and KitGuru have configured a test bench which can deliver up to a 2,000 watt DC load. Due to public requests we have changed our temperature settings recently – previously we rated with ambient temperatures at 25C, we have increased ambient temperatures by 10c (to 35c) in our environment to greater reflect warmer internal chassis conditions.

We use combinations of the following hardware:
• SunMoon SM-268
• CSI3710A Programmable DC load (+3.3V and +5V outputs)
• CSI3711A Programmable DC load (+12V1, +12V2, +12V3, and +12V4)
• Extech Power Analyzer
• Extech MultiMaster MM570 digital multimeter
• SkyTronic DSL 2 Digital Sound Level Meter (6-130dBa)
• Digital oscilloscope (20M S/s with 12 Bit ADC)
• Variable Autotransformer, 1.4 KVA

DC Output Load Regulation
Combined DC Load	+3.3V		+5V		+12V		+5VSB		-12V
	A	V	A	V	A	V	A	V	A	V
100W	1.55	3.34	1.78	5.05	6.65	12.05	0.50	5.05	0.20	-12.01
250W	3.45	3.32	4.40	5.02	17.17	12.02	1.00	5.02	0.30	-12.02
500W	7.04	3.29	9.11	5.00	34.63	11.97	2.00	5.01	0.50	-12.04
750W	11.02	3.27	13.73	4.98	52.79	11.94	2.50	4.98	0.60	-12.06
1000W	16.89	3.26	18.95	4.94	71.23	11.93	3.00	4.95	0.80	-12.08

This power supply produced solid load regulation across all outputs, even when delivering the full 1000W. All rails held within 1.5% of the reference voltage, well in excess of the +/-5% threshold.

Silverstone Strider Plus 1000W	Maximum Load
	1134W

We managed to get another 134W from the power supply before the protection circuitry kicked in. We are happy to report a safe shut down verifying that the overcircuit protection is doing its job.

Next we want to try Cross Loading. This basically means loads which are not balanced. If a PC for instance needs 500W on the +12V outputs but something like 30W via the combined 3.3V and +5V outputs then the voltage regulation can fluctuate badly.

Cross Load Testing	+3.3V		+5V		+12V		-12V		+5VSB
	A	V	A	V	A	V	A	V	A	V
885W	2.0	3.32	2.0	5.02	72.0	11.92	0.2	-12.00	0.50	5.02
240W	20.0	3.26	24.0	4.95	2.0	12.02	0.2	-12.04	0.50	4.96

The Silverstone PSU handled the Cross loading tests very well and we didn’t experience any issues at all. All the voltages remained well within specification.

We then used an oscilloscope to measure AC ripple and noise present on the DC outputs. We set the oscilloscope time base to check for AC ripple at both high and low ends of the spectrum. ATX12V V2.2 specification for DC output ripple and noise is defined in the ATX 12V power supply design guide.

ATX12V Ver 2.2 Noise/Ripple Tolerance
Output	Ripple (mV p-p)
+3.3V	50
+5V	50
+12V1	120
+12V2	120
-12V	120
+5VSB	50

Obviously when measuring AC noise and ripple on the DC outputs the cleaner (less recorded) means we have a better end result. We measured this AC signal amplitude to see how closely the Silver Stone unit complied with the ATX standard.

AC Ripple (mV p-p)
DC Load	+3.3V	+5V	+12V	5VSB
100W	10	15	15	10
250W	15	15	20	10
500W	20	25	30	15
750W	30	30	35	20
1000W	35	35	45	30

The +12V rail shows great ripple control, generating 45 mV at full load, well within specifications. The +3.3V and +5V rails aren't quite so impressive however, peaking at 35mV, but still within industry specifications.

Efficiency (%)
100W	85.78
250W	87.74
500W	89.13
750W	87.07
1000W	85.57

The efficiency results are quite good, achieving 80 Plus Silver Certification, barely.

We take the issue of noise very seriously at KitGuru and this is why we have built a special home brew system as a reference point when we test noise levels of various components. Why do this? Well this means we can eliminate secondary noise pollution in the test room and concentrate on components we are testing. It also brings us slightly closer to industry standards, such as DIN 45635.

Today to test the Power Supply we have taken it into our acoustics room environment and have set our SkyTronic DSL 2 Digital Sound Level Meter (6-130dBa) one meter away from the unit. We have no other fans running so we can effectively measure just the noise from the unit itself.

As this can be a little confusing for people, here are various dBa ratings in with real world situations to help describe the various levels.

KitGuru noise guide
10dBA – Normal Breathing/Rustling Leaves
20-25dBA – Whisper
30dBA – High Quality Computer fan
40dBA – A Bubbling Brook, or a Refridgerator
50dBA – Normal Conversation
60dBA – Laughter
70dBA – Vacuum Cleaner or Hairdryer
80dBA – City Traffic or a Garbage Disposal
90dBA – Motorcycle or Lawnmower
100dBA – MP3 Player at maximum output
110dBA – Orchestra
120dBA – Front row rock concert/Jet Engine
130dBA – Threshold of Pain
140dBA – Military Jet takeoff/Gunshot (close range)
160dBA – Instant Perforation of eardrum

Noise (dBA)
100W	28.9
250W	28.9
500W	30.4
750W	32.5
1000W	35.2

The Silverstone Strider Plus 1000W is very quiet throughout all the range, and only in the last 250W of power output does it become audible, peaking around 35 dBa. Great results.

Temperature (c)
	Intake	Exhaust
100W	35	37
250W	35	39
500W	38	43
750W	43	50
1000W	46	56

The large fan handles air flow very well and under 50% load the exhaust temperature doesn’t rise that much compared to the intake air. Only around 750W does the fan spin up more to help compensate for rising ambient temperatures. A good balance of low noise levels with strong air flow.

Maximum load	Efficiency
1134W	83.45

Pushing the PSU above its rated limits generates an efficiency level of around 83.45%. This is not a viable ‘real world’ situation, but its interesting nonetheless.

Become a Patron!