Seasonic Prime Ultra Titanium 1000W Power Supply Review

1. Introduction2. Bundle & Cabling3. External4. Internal5. Testing & Methodology6. Closing Thoughts7. View All Pages

Correctly testing power supplies is a complex procedure and KitGuru have configured a test bench which can deliver up to a 2,000 watt DC load.

We test ambient temperatures at 35c in our environment to greater reflect warmer internal chassis conditions.

We use combinations of the following hardware:
• SunMoon SM-268
• CSI3710A Programmable DC load (+3.3V and +5V outputs)
• CSI3711A Programmable DC load (+12V1, +12V2, +12V3, and +12V4)
• Extech Power Analyzer
• Extech MultiMaster MM570 digital multimeter
• SkyTronic DSL 2 Digital Sound Level Meter (6-130dBa)
• Digital oscilloscope (20M S/s with 12 Bit ADC)
• Variable Autotransformer, 1.4 KVA

DC Output Load Regulation
Combined DC Load	+3.3V		+5V		+12V		+5VSB		-12V
	A	V	A	V	A	V	A	V	A	V
100W	0.88	3.33	0.90	5.02	7.35	12.19	0.50	5.01	0.20	-12.03
200W	1.60	3.33	1.65	5.02	15.10	12.19	1.00	5.01	0.20	-12.03
500W	3.20	3.33	3.25	5.01	38.60	12.19	1.50	5.00	0.20	-12.02
750W	4.05	3.32	4.15	5.01	58.50	12.19	2.00	5.00	0.30	-12.01
1000W	5.45	3.32	5.50	5.01	78.09	12.18	2.50	5.00	0.30	-12.01

The load regulation of this power supply is absolutely magnificent, with all rails holding close to reference levels (within .3%).

Seasonic PRIME 1000W Titanium	Maximum Load
	1304W

We managed to get another 304W from the power supply before the protection circuitry kicked in! The supply was undamaged and it was ready to fire up again when we were a little more sensible with the load. Those caps are massively overspec'd.

Next we want to try Cross Loading. This basically means loads which are not balanced. If a PC for instance needs 500W on the +12V outputs but something like 30W via the combined 3.3V and +5V outputs then the voltage regulation can fluctuate badly.

Cross Load Testing	+3.3V		+5V		+12V		-12V		+5VSB
	A	V	A	V	A	V	A	V	A	V
885W	2.0	3.33	2.0	5.02	72.0	12.18	0.2	-12.02	0.50	5.01
240W	20.0	3.32	24.0	5.01	2.0	12.20	0.2	-12.03	0.50	5.00

The Seasonic supply handled the Cross load tests without any concerns. Close to class leading results.

We then used an oscilloscope to measure AC ripple and noise present on the DC outputs. We set the oscilloscope time base to check for AC ripple at both high and low ends of the spectrum. ATX12V V2.2 specification for DC output ripple and noise is defined in the ATX 12V power supply design guide.

ATX12V Ver 2.2 Noise/Ripple Tolerance
Output	Ripple (mV p-p)
+3.3V	50
+5V	50
+12V1	120
+12V2	120
-12V	120
+5VSB	50

Obviously when measuring AC noise and ripple on the DC outputs the cleaner (less recorded) means we have a better end result. We measured this AC signal amplitude to see how closely the unit complied with the ATX standard.

AC Ripple (mV p-p)
DC Load	+3.3V	+5V	+12V	5VSB
100W	5	5	5	5
250W	5	5	5	5
500W	5	5	10	5
750W	10	5	10	5
1000W	10	10	15	5

Ripple suppression from this unit is great peaking at 10mV on both +3.3V and +5V rails. The +12V rail peaks at 15mV, another great result.

Efficiency (%)
100W	92.14
250W	94.52
500W	96.11
750W	95.32
1000W	94.23

The efficiency results are excellent, peaking at 96% at close to 50%. This drops to 94.2% efficiency at full load. Great results all round from this unit.

We take the issue of noise very seriously at KitGuru and this is why we have built a special home brew system as a reference point when we test noise levels of various components. Why do this? Well this means we can eliminate secondary noise pollution in the test room and concentrate on components we are testing. It also brings us slightly closer to industry standards, such as DIN 45635.

Today to test the Power Supply we have taken it into our acoustics room environment and have set our SkyTronic DSL 2 Digital Sound Level Meter (6-130dBa) one meter away from the unit. We have no other fans running so we can effectively measure just the noise from the unit itself.

As this can be a little confusing for people, here are various dBa ratings in with real world situations to help describe the various levels.

KitGuru noise guide
10dBA – Normal Breathing/Rustling Leaves
20-25dBA – Whisper
30dBA – High Quality Computer fan
40dBA – A Bubbling Brook, or a Refridgerator
50dBA – Normal Conversation
60dBA – Laughter
70dBA – Vacuum Cleaner or Hairdryer
80dBA – City Traffic or a Garbage Disposal
90dBA – Motorcycle or Lawnmower
100dBA – MP3 Player at maximum output
110dBA – Orchestra
120dBA – Front row rock concert/Jet Engine
130dBA – Threshold of Pain
140dBA – Military Jet takeoff/Gunshot (close range)
160dBA – Instant Perforation of eardrum

Noise (dBA)
100W	<28.0
250W	<28.0
500W	29.5
750W	32.7
1000W	33.9

Under most load conditions the fan will make little, if any noise. Under higher load situations the fan will be heard, but it never spins fast enough to become intrusive, or a problem. If you run with the Hybrid mode enabled, the fan didn’t spin up at all under a 400 watt load – during our tests anyway.

Temperature (c)
	Intake	Exhaust
100W	35	39
250W	35	43
500W	38	49
750W	43	56
1000W	46	61

With the high efficiency of this unit, the temperatures are well maintained throughout the full range of the thermal curve.

Maximum load	Efficiency
1304W	92.8

Pushing the PSU above its rated limits generates an efficiency level of around 92.8%. This is not a viable ‘real world’ situation, but its interesting nonetheless.

Become a Patron!