Enermax NAXN 850W Power Supply Review

1. Introduction2. Enermax NAXN 850W Power Supply (Bundle and Cables)3. Enermax NAXN 850W Power Supply (Exterior)4. Enermax NAXN 850W Power Supply (Interior)5. Testing Methodology and Results6. Closing Thoughts7. View All Pages

Additional technical assistance: Peter McFarland and Jeremy Price.

Correctly testing power supplies is a complex procedure and KitGuru have configured a test bench which can deliver up to a 2,000 watt DC load. Due to public requests we have changed our temperature settings recently – previously we rated with ambient temperatures at 25C, we have increased ambient temperatures by 10c (to 35c) in our environment to greater reflect warmer internal chassis conditions.

We use combinations of the following hardware:
• SunMoon SM-268
• CSI3710A Programmable DC load (+3.3V and +5V outputs)
• CSI3711A Programmable DC load (+12V1, +12V2, +12V3, and +12V4)
• Extech Power Analyzer
• Extech MultiMaster MM570 digital multimeter
• Extech digital sound level meter
• Digital oscilloscope (20M S/s with 12 Bit ADC)
• Variable Autotransformer, 1.4 KVA

DC Output Load Regulation
Combined DC Load	+3.3V		+5V		+12V		+5VSB		-12V
	A	V	A	V	A	V	A	V	A	V
100W	1.56	3.37	1.77	5.04	6.62	12.15	0.50	5.05	0.20	-12.15
225W	3.72	3.35	3.83	5.03	15.52	12.08	1.00	5.04	0.20	-12.13
450W	7.52	3.33	8.34	5.02	30.66	12.05	1.50	5.03	0.30	-12.13
675W	11.32	3.30	12.37	5.01	47.44	11.95	2.00	4.98	0.50	-12.12
850W	1.41	3.27	1.15	5.00	63.34	11.86	0.50	4.95	0.20	-12.12

The NAXN 850W delivered excellent load regulation on all output channels across a wide range of loads. These are good results and the +3.3V and 5V rails remained firmly within +/-2% of the nominal voltage instead of the recommended +/-5%.

Enermax NAXN 850W	Maximum Load
	915W

We managed to get the PSU to hit 915W before it would shut down. delivering around 65W more than the rated specifications. It would run at 900W for quite a while.

Next we want to try Cross Loading. This basically means loads which are not balanced. If a PC for instance needs 500W on the +12V outputs but something like 30W via the combined 3.3V and +5V outputs then the voltage regulation can fluctuate badly.

Cross Load Testing	+3.3V		+5V		+12V		-12V		+5VSB
	A	V	A	V	A	V	A	V	A	V
760W	1.0	3.27	1.0	5.02	60.0	11.77	0.2	-12.04	0.50	5.00
165W	15.0	3.28	18.0	4.97	2.0	12.03	0.2	-12.02	0.50	4.97

Again, these are very good results with fluctuation held safely within the rated parameters, even when loading the unit with 60A on the 12V. The +12V rail dipped a little, but it is still safe enough.

We then used an oscilloscope to measure AC ripple and noise present on the DC outputs. We set the oscilloscope time base to check for AC ripple at both high and low ends of the spectrum.

ATX12V V2.2 specification for DC output ripple and noise is defined in the ATX 12V power supply design guide.

ATX12V Ver 2.2 Noise/Ripple Tolerance
Output	Ripple (mV p-p)
+3.3V	50
+5V	50
+12V1	120
+12V2	120
-12V	120
+5VSB	50

Obviously when measuring AC noise and ripple on the DC outputs the cleaner (less recorded) means we have a better end result. We measured this AC signal amplitude to see how closely the Enermax unit complied with the ATX standard.

AC Ripple (mV p-p)
DC Load	+3.3V	+5V	+12V	5VSB
100W	5	10	15	10
225W	10	15	15	15
450W	10	15	20	15
675W	15	15	30	15
850W	20	15	40	15

Ripple results are very impressive, across the board. The 12V rail registered around 40 mV with our equipment, which is well within the Tolerance guidelines.

Efficiency (%)
100W	84.57
225W	85.63
450W	87.86
675W	86.59
850W	85.23

For a 80 Plus Bronze specified unit, these results are very strong, showing a maximum efficiency rating, just shy of 88%. At maximum load this drops to around 86%, which is again, a great result.

We take the issue of noise very seriously at KitGuru and this is why we have built a special home brew system as a reference point when we test noise levels of various components. Why do this? Well this means we can eliminate secondary noise pollution in the test room and concentrate on components we are testing. It also brings us slightly closer to industry standards, such as DIN 45635.

Today to test the Corsair Power Supply we have taken it into our acoustics room environment and have set our Digital Sound Level Noise Decibel Meter Style 2 one meter away from the unit. We have no other fans running so we can effectively measure just the noise from the unit itself.

As this can be a little confusing for people, here are various dBa ratings in with real world situations to help describe the various levels.

KitGuru noise guide
10dBA – Normal Breathing/Rustling Leaves
20-25dBA – Whisper
30dBA – High Quality Computer fan
40dBA – A Bubbling Brook, or a Refridgerator
50dBA – Normal Conversation
60dBA – Laughter
70dBA – Vacuum Cleaner or Hairdryer
80dBA – City Traffic or a Garbage Disposal
90dBA – Motorcycle or Lawnmower
100dBA – MP3 Player at maximum output
110dBA – Orchestra
120dBA – Front row rock concert/Jet Engine
130dBA – Threshold of Pain
140dBA – Military Jet takeoff/Gunshot (close range)
160dBA – Instant Perforation of eardrum

Noise (dBA)
100W	27.7
225W	28.8
450W	31.3
675W	33.8
850W	36.3

The power supply is quiet at moderate load and only becomes audible in the upper 30% of the power delivery, rising to around 36 dBa at full load.

Temperature (c)
	Intake	Exhaust
100W	36	38
225W	37	40
450W	39	45
675W	43	49
850W	45	54

Exhaust temperatures are good in the lower end of the spectrum, rising to a 9c above ambient result at full load. The 120mm is quiet and spins under 1,300 rpm at all times.

Maximum load	Efficiency
915W	83.12%

For those interested, we measured efficiency when stressing the unit to breaking point. Over 83% at 915W … hardly practical, but interesting regardless.

Become a Patron!