Cyonic AU-650x Full Modular PSU Review

1. Introduction2. Cyonic AU-650x (Bundle & Cables)3. Cyonic AU-650x (External)4. Cyonic AU-650x (Internal)5. High Res Gallery6. Testing & Methodology7. Closing Thoughts8. View All Pages

Additional technical assistance: Peter McFarland and Jeremy Price.

Correctly testing power supplies is a complex procedure and KitGuru have configured a test bench which can deliver up to a 2,000 watt DC load. Due to public requests we have changed our temperature settings recently – previously we rated with ambient temperatures at 25C, we have increased ambient temperatures by 10c (to 35c) in our environment to greater reflect warmer internal chassis conditions.

We use combinations of the following hardware:

• SunMoon SM-268
• CSI3710A Programmable DC load (+3.3V and +5V outputs)
• CSI3711A Programmable DC load (+12V1, +12V2, +12V3, and +12V4)
• Extech Power Analyzer
• Extech MultiMaster MM570 digital multimeter
• SkyTronic DSL 2 Digital Sound Level Meter (6-130dBa)
• Digital oscilloscope (20M S/s with 12 Bit ADC)
• Variable Autotransformer, 1.4 KVA

We combine all +12V output for the results below.

DC Output Load Regulation
Combined DC Load	+3.3V		+5V		+12V		+5VSB		-12V
	A	V	A	V	A	V	A	V	A	V
152W	2.05	3.35	2.04	5.04	10.12	12.12	0.50	4.99	0.20	-12.04
270W	3.03	3.35	3.05	5.04	19.14	12.09	0.50	4.98	0.30	-12.05
400W	4.05	3.34	5.02	5.02	29.18	12.06	1.00	4.98	0.30	-12.05
523W	6.09	3.34	7.04	4.98	38.18	12.04	1.50	4.98	0.30	-12.06
650W	8.00	3.33	9.00	4.96	48.00	12.02	2.50	4.98	0.30	-12.08

Load regulation is good across the output range. No concerns here.

Next we want to try Cross Loading. This basically means loads which are not balanced. If a PC for instance needs 500W on the +12V outputs but something like 30W via the combined 3.3V and +5V outputs then the voltage regulation can fluctuate badly.

Cross Load Testing	+3.3V		+5V		+12V		-12V		+5VSB
	A	V	A	V	A	V	A	V	A	V
590W	1.0	3.35	1.0	5.04	48.0	12.01	0.2	-12.04	0.50	4.98
145W	12.0	3.31	15.0	4.95	2.0	12.11	0.2	-12.03	0.50	4.97

The unit passed our cross load test without a problem.

We then used an oscilloscope to measure AC ripple and noise present on the DC outputs. We set the oscilloscope time base to check for AC ripple at both high and low ends of the spectrum. ATX12V V2.2 specification for DC output ripple and noise is defined in the ATX 12V power supply design guide.

ATX12V Ver 2.2 Noise/Ripple Tolerance
Output	Ripple (mV p-p)
+3.3V	50
+5V	50
+12V1	120
+12V2	120
-12V	120
+5VSB	50

Obviously when measuring AC noise and ripple on the DC outputs the cleaner (less recorded) means we have a better end result. We measured this AC signal amplitude to see how closely the unit complied with the ATX standard.

AC Ripple (mV p-p)
DC Load	+3.3V	+5V	+12V	5VSB
152W	10	10	15	10
270W	10	15	15	10
400W	15	15	20	15
523W	15	20	30	15
650W	15	20	35	20

Ripple suppression falls within the rated tolerance guidelines. The +3.3V and +5V output peak at 15mV and 20mV respectively. The +12V output hits 35mV at full load which is well within the rated guidelines.

Efficiency (%)
152W	87.39
270W	91.83
400W	90.87
523W	89.11
650W	88.82

Efficiency is good – peaking just under 91 percent at 50 percent load. At full load this drops to around 89 percent efficiency.

We take the issue of noise very seriously at KitGuru and this is why we have built a special home brew system as a reference point when we test noise levels of various components. Why do this? Well this means we can eliminate secondary noise pollution in the test room and concentrate on components we are testing. It also brings us slightly closer to industry standards, such as DIN 45635.

Today to test the Power Supply we have taken it into our acoustics room environment and have set our SkyTronic DSL 2 Digital Sound Level Meter (6-130dBa) one meter away from the unit. We have no other fans running so we can effectively measure just the noise from the unit itself.

As this can be a little confusing for people, here are various dBa ratings in with real world situations to help describe the various levels.

KitGuru noise guide

10dBA – Normal Breathing/Rustling Leaves
20-25dBA – Whisper
30dBA – High Quality Computer fan
40dBA – A Bubbling Brook, or a Refrigerator
50dBA – Normal Conversation
60dBA – Laughter
70dBA – Vacuum Cleaner or Hairdryer
80dBA – City Traffic or a Garbage Disposal
90dBA – Motorcycle or Lawnmower
100dBA – MP3 Player at maximum output
110dBA – Orchestra
120dBA – Front row rock concert/Jet Engine
130dBA – Threshold of Pain
140dBA – Military Jet takeoff/Gunshot (close range)
160dBA – Instant Perforation of eardrum

Noise (dBA)
152W	<28.0
270W	<28.0
400W	30.5
523W	32.9
650W	34.2

The fan inside the AU-650x is quiet throughout most of the range, hitting around 34dBa at full load. This is exactly what we want to see from a quality FDB fan.

Temperature (c)
	Intake	Exhaust
152W	36	39
270W	39	42
400W	42	45
523W	43	54
650W	45	59

The fan doesn't work too hard until around the last 20% of power output. Temperatures are well controlled throughout.

Become a Patron!