Antec TruePower New 650W Power Supply Review

1. Introduction2. The Antec TruePower new 650W (Bundle & External)3. The Antec TruePower new 650W (Internal)4. Testing Methodology and Results5. Closing Thoughts6. View All Pages

Additional technical assistance: Peter McFarland and Jeremy Price.

Correctly testing power supplies is a complex procedure and KitGuru have configured a test bench which can deliver up to a 2,000 watt DC load. Due to public requests we have changed our temperature settings recently – previously we rated with ambient temperatures at 25C, we have increased ambient temperatures by 10c (to 35c) in our environment to greater reflect warmer internal chassis conditions.

We use combinations of the following hardware:
• SunMoon SM-268
• CSI3710A Programmable DC load (+3.3V and +5V outputs)
• CSI3711A Programmable DC load (+12V1, +12V2, +12V3, and +12V4)
• Extech Power Analyzer
• Extech MultiMaster MM570 digital multimeter
• SkyTronic DSL 2 Digital Sound Level Meter (6-130dBa)
• Digital oscilloscope (20M S/s with 12 Bit ADC)
• Variable Autotransformer, 1.4 KVA

DC Output Load Regulation
Combined DC Load	+3.3V		+5V		+12V		+5VSB		-12V
	A	V	A	V	A	V	A	V	A	V
152W	2.07	3.34	2.02	5.06	10.03	12.13	0.50	5.05	0.20	-12.11
270W	3.02	3.34	3.01	5.05	19.05	12.11	0.50	5.04	0.30	-12.09
400W	4.04	3.33	5.01	5.05	29.21	12.06	1.00	5.04	0.30	-12.08
523W	6.00	3.32	7.08	5.04	38.14	12.05	1.50	5.02	0.30	-12.06
652W	8.03	3.31	9.02	5.01	48.31	12.03	2.50	4.99	0.30	-12.04

A great set of load results for the Antec power supply, all of the primary rails are holding within 2.5% of the nominal voltage.

Antec Truepower New 650W	Maximum Load
	714.5W

We managed to push the power supply to around 715w before it shut down, gracefully. The protection circuitry is working well.

Next we want to try Cross Loading. This basically means loads which are not balanced. If a PC for instance needs 500W on the +12V outputs but something like 30W via the combined 3.3V and +5V outputs then the voltage regulation can fluctuate badly.

Cross Load Testing	+3.3V		+5V		+12V		-12V		+5VSB
	A	V	A	V	A	V	A	V	A	V
590W	1.0	3.34	1.0	5.04	48.0	12.00	0.2	-12.11	0.50	5.03
145W	12.0	3.28	15.0	5.01	2.0	11.98	0.2	-12.03	0.50	5.01

The XFX PSU handled the Cross loading tests without a problem and we experienced no issues. All the voltages remained within stated tolerances.

We then used an oscilloscope to measure AC ripple and noise present on the DC outputs. We set the oscilloscope time base to check for AC ripple at both high and low ends of the spectrum. ATX12V V2.2 specification for DC output ripple and noise is defined in the ATX 12V power supply design guide.

ATX12V Ver 2.2 Noise/Ripple Tolerance
Output	Ripple (mV p-p)
+3.3V	50
+5V	50
+12V1	120
+12V2	120
-12V	120
+5VSB	50

Obviously when measuring AC noise and ripple on the DC outputs the cleaner (less recorded) means we have a better end result. We measured this AC signal amplitude to see how closely the Antec unit complied with the ATX standard.

AC Ripple (mV p-p)
DC Load	+3.3V	+5V	+12V	5VSB
152W	10	10	10	10
270W	15	15	15	10
400W	15	15	15	10
523W	15	15	20	15
652W	20	15	25	15

A very strong set of results for the Antec TruePower with a particularly impressive 12V result of 25mv under maximum load.

Efficiency (%)
152W	84.21
270W	86.76
400W	87.12
523W	85.21
652W	84.01

These efficiency results are great across the range of loads, holding well within 80 Plus Bronze certification requirements.

We take the issue of noise very seriously at KitGuru and this is why we have built a special home brew system as a reference point when we test noise levels of various components. Why do this? Well this means we can eliminate secondary noise pollution in the test room and concentrate on components we are testing. It also brings us slightly closer to industry standards, such as DIN 45635.

Today to test the Power Supply we have taken it into our acoustics room environment and have set our SkyTronic DSL 2 Digital Sound Level Meter (6-130dBa) one meter away from the unit. We have no other fans running so we can effectively measure just the noise from the unit itself.

As this can be a little confusing for people, here are various dBa ratings in with real world situations to help describe the various levels.

KitGuru noise guide
10dBA – Normal Breathing/Rustling Leaves
20-25dBA – Whisper
30dBA – High Quality Computer fan
40dBA – A Bubbling Brook, or a Refridgerator
50dBA – Normal Conversation
60dBA – Laughter
70dBA – Vacuum Cleaner or Hairdryer
80dBA – City Traffic or a Garbage Disposal
90dBA – Motorcycle or Lawnmower
100dBA – MP3 Player at maximum output
110dBA – Orchestra
120dBA – Front row rock concert/Jet Engine
130dBA – Threshold of Pain
140dBA – Military Jet takeoff/Gunshot (close range)
160dBA – Instant Perforation of eardrum

Noise (dBA)
152W	28.3
270W	29.2
400W	29.7
523W	33.5
652W	36.1

At around 70% load the PSU becomes audible rising to around 36 dBa at 100% load.

Temperature (c)
	Intake	Exhaust
152W	35	37
270W	35	38
400W	38	45
523W	42	50
652W	45	53

The large ADDA fan is very capable, managing to maintain a 8c above ambient intake threshold at full load. Very impressive.

Maximum Load	Efficiency
714.5W	80.7

Pushing the PSU above its rated limits generates an efficiency level of around 80.7%. This is not a viable ‘real world’ situation, but its interesting nonetheless.

Become a Patron!