Antec High Current Pro 850W Power Supply Review

1. Introduction2. Antec High Current Pro 850W (Bundle)3. Antec High Current Pro 850W (External)4. Antec High Current Pro 850W (Internal)5. Testing Methodology and Results6. Closing Thoughts7. View All Pages

Additional technical assistance: Peter McFarland and Jeremy Price.

Correctly testing power supplies is a complex procedure and KitGuru have configured a test bench which can deliver up to a 2,000 watt DC load. Due to public requests we have changed our temperature settings recently – previously we rated with ambient temperatures at 25C, we have increased ambient temperatures by 10c (to 35c) in our environment to greater reflect warmer internal chassis conditions.

We use combinations of the following hardware:
• SunMoon SM-268
• CSI3710A Programmable DC load (+3.3V and +5V outputs)
• CSI3711A Programmable DC load (+12V1, +12V2, +12V3, and +12V4)
• Extech Power Analyzer
• Extech MultiMaster MM570 digital multimeter
• SkyTronic DSL 2 Digital Sound Level Meter (6-130dBa)
• Digital oscilloscope (20M S/s with 12 Bit ADC)
• Variable Autotransformer, 1.4 KVA

All 12V outputs are combined into a single rail for testing.

DC Output Load Regulation
Combined DC Load	+3.3V		+5V		+12V		+5VSB		-12V
	A	V	A	V	A	V	A	V	A	V
100W	1.58	3.38	1.19	5.11	6.65	12.14	0.50	5.05	0.20	-12.12
225W	3.70	3.36	2.80	5.07	15.54	12.09	1.00	5.03	0.20	-12.09
450W	7.51	3.33	6.00	5.04	30.67	12.03	1.50	5.02	0.30	-12.05
675W	11.32	3.31	10.87	5.02	47.48	11.94	2.00	5.01	0.50	-12.02
850W	1.29	3.29	1.11	5.01	71.00	11.90	0.50	4.99	0.20	-11.97

A solid set of results for the Antec High Current Pro 850W Supply, falling well within the +/-5% nominal rated specifications. At 71 Amps on the 12V output, we recorded 11.90V.

Antec HCP 850W	Maximum Load
	965.8W

We managed to squeeze 965.8W out of the supply before it shut down.

Next we want to try Cross Loading. This basically means loads which are not balanced. If a PC for instance needs 500W on the +12V outputs but something like 30W via the combined 3.3V and +5V outputs then the voltage regulation can fluctuate badly.

Cross Load Testing	+3.3V		+5V		+12V		-12V		+5VSB
	A	V	A	V	A	V	A	V	A	V
760W	1.0	3.37	1.0	5.08	65.0	11.87	0.2	12.11	0.50	5.06
165W	15.0	3.26	18.0	4.97	2.0	12.12	0.2	-11.95	0.50	5.04

Cross loading results from the Delta/Antec design are impressive, with some fluctuation on the 12v rail.

We then used an oscilloscope to measure AC ripple and noise present on the DC outputs. We set the oscilloscope time base to check for AC ripple at both high and low ends of the spectrum.

ATX12V V2.2 specification for DC output ripple and noise is defined in the ATX 12V power supply design guide.

ATX12V Ver 2.2 Noise/Ripple Tolerance
Output	Ripple (mV p-p)
+3.3V	50
+5V	50
+12V1	120
+12V2	120
-12V	120
+5VSB	50

Obviously when measuring AC noise and ripple on the DC outputs the cleaner (less recorded) means we have a better end result. We measured this AC signal amplitude to see how closely the Antec unit complied with the ATX standard.

AC Ripple (mV p-p)
DC Load	+3.3V	+5V	+12V	5VSB
100W	5	5	5	5
225W	5	5	10	10
450W	10	15	10	10
675W	10	20	15	15
850W	15	25	20	15

Ripple results are well within the parameters set down in the ATX12V Ver 2.2 standard.

Efficiency (%)
100W	84.75
225W	89.13
450W	92.09
675W	91.31
850W	90.31

Great efficiency ratings across the full range of supply loads, achieving the 80 Plus Gold rating. At full load the efficiency is still over 90 percent which is extremely impressive.

We take the issue of noise very seriously at KitGuru and this is why we have built a special home brew system as a reference point when we test noise levels of various components. Why do this? Well this means we can eliminate secondary noise pollution in the test room and concentrate on components we are testing. It also brings us slightly closer to industry standards, such as DIN 45635.

Today to test the Power Supply we have taken it into our acoustics room environment and have set our SkyTronic DSL 2 Digital Sound Level Meter (6-130dBa) one meter away from the unit. We have no other fans running so we can effectively measure just the noise from the unit itself.

As this can be a little confusing for people, here are various dBa ratings in with real world situations to help describe the various levels.

KitGuru noise guide
10dBA – Normal Breathing/Rustling Leaves
20-25dBA – Whisper
30dBA – High Quality Computer fan
40dBA – A Bubbling Brook, or a Refridgerator
50dBA – Normal Conversation
60dBA – Laughter
70dBA – Vacuum Cleaner or Hairdryer
80dBA – City Traffic or a Garbage Disposal
90dBA – Motorcycle or Lawnmower
100dBA – MP3 Player at maximum output
110dBA – Orchestra
120dBA – Front row rock concert/Jet Engine
130dBA – Threshold of Pain
140dBA – Military Jet takeoff/Gunshot (close range)
160dBA – Instant Perforation of eardrum

Noise (dBA)
100W	25.7
225W	27.3
450W	28.8
675W	30.3
850W	32.7

This is clearly one of the quieter performance power supplies we have tested. It is generally operating well under 30 dBA when loaded, which is basically inaudible within an enthusiast system.

Temperature (c)
	Intake	Exhaust
100W	35	36
225W	35	37
450W	38	44
675W	42	51
850W	45	54

The large fan helps to keep noise to a minimum, while forcing a high level of airflow across the internal components. At full load we reach a 9c above ambient intake threshold.

Maximum load	Efficiency
965.8W	82.7

Pushing the PSU above its rated limits generates an efficiency level of around 82.7%. This is not a viable ‘real world’ situation, but its interesting nonetheless.

Become a Patron!