ADATA HM Series 650W Power Supply Review

1. Introduction2. The ADATA HM Series 650W PSU (Bundle/Cabling)3. ADATA HM Series 650W Power Supply (External)4. ADATA HM Series 650W Power Supply (Internal)5. Testing Methodology and Results6. Closing Thoughts7. View All Pages

Additional technical assistance: Peter McFarland and Jeremy Price.

Correctly testing power supplies is a complex procedure and KitGuru have configured a test bench which can deliver up to a 2,000 watt DC load. Due to public requests we have changed our temperature settings recently – previously we rated with ambient temperatures at 25C, we have increased ambient temperatures by 10c (to 35c) in our environment to greater reflect warmer internal chassis conditions.

We use combinations of the following hardware:
• SunMoon SM-268
• CSI3710A Programmable DC load (+3.3V and +5V outputs)
• CSI3711A Programmable DC load (+12V1, +12V2, +12V3, and +12V4)
• Extech Power Analyzer
• Extech MultiMaster MM570 digital multimeter
• SkyTronic DSL 2 Digital Sound Level Meter (6-130dBa)
• Digital oscilloscope (20M S/s with 12 Bit ADC)
• Variable Autotransformer, 1.4 KVA

DC Output Load Regulation
Combined DC Load	+3.3V		+5V		+12V		+5VSB		-12V
	A	V	A	V	A	V	A	V	A	V
152W	2.07	3.34	2.02	5.03	10.03	12.07	0.50	5.05	0.20	-12.08
270W	3.02	3.34	3.01	5.01	19.05	12.06	0.50	5.03	0.30	-12.08
400W	4.04	3.33	5.01	5.00	29.21	12.04	1.00	5.02	0.30	-12.07
523W	6.00	3.32	7.08	4.99	38.14	12.01	1.50	4.99	0.30	-12.05
652W	8.03	3.30	9.02	4.98	48.31	11.97	2.50	4.98	0.30	-12.02

Output load regulation is good from this supply, holding all primary rails within 2.5% of the nominal voltage.

ADATA HM 650W	Maximum Load
	715.8W

The power supply would shut down at 715.8W, gracefully. We found the protection circuitry to work very well.

Next we want to try Cross Loading. This basically means loads which are not balanced. If a PC for instance needs 500W on the +12V outputs but something like 30W via the combined 3.3V and +5V outputs then the voltage regulation can fluctuate badly.

Cross Load Testing	+3.3V		+5V		+12V		-12V		+5VSB
	A	V	A	V	A	V	A	V	A	V
590W	1.0	3.31	1.0	5.02	48.0	11.92	0.2	-12.06	0.50	5.02
145W	12.0	3.28	15.0	4.97	2.0	12.03	0.2	-12.02	0.50	5.01

The ADATA HM 650W PSU handled our Cross loading tests without a problem and we didn't experience any issues during this phase. All voltages remained within stated tolerances.

We then used an oscilloscope to measure AC ripple and noise present on the DC outputs. We set the oscilloscope time base to check for AC ripple at both high and low ends of the spectrum. ATX12V V2.2 specification for DC output ripple and noise is defined in the ATX 12V power supply design guide.

ATX12V Ver 2.2 Noise/Ripple Tolerance
Output	Ripple (mV p-p)
+3.3V	50
+5V	50
+12V1	120
+12V2	120
-12V	120
+5VSB	50

Obviously when measuring AC noise and ripple on the DC outputs the cleaner (less recorded) means we have a better end result. We measured this AC signal amplitude to see how closely the XFX unit complied with the ATX standard.

AC Ripple (mV p-p)
DC Load	+3.3V	+5V	+12V	5VSB
152W	5	5	10	5
270W	5	5	10	5
400W	5	5	15	10
523W	5	10	25	10
652W	10	10	35	10

Ripple results are well within the parameters set down in the ATX12V Ver 2.2 standard. +3.3V and +5V are extremely impressive and the +12V rail is also very stable, never exceeding 35mv.

Efficiency (%)
152W	82.43
270W	83.62
400W	86.17
523W	84.73
652W	82.12

Very solid results for the ADATA 80 Plus Bronze Certified power supply, hitting just over 86 percent at 50 percent load. At full load the efficiency drops to around 82%, still a good result.

We take the issue of noise very seriously at KitGuru and this is why we have built a special home brew system as a reference point when we test noise levels of various components. Why do this? Well this means we can eliminate secondary noise pollution in the test room and concentrate on components we are testing. It also brings us slightly closer to industry standards, such as DIN 45635.

Today to test the Power Supply we have taken it into our acoustics room environment and have set our SkyTronic DSL 2 Digital Sound Level Meter (6-130dBa) one meter away from the unit. We have no other fans running so we can effectively measure just the noise from the unit itself.

As this can be a little confusing for people, here are various dBa ratings in with real world situations to help describe the various levels.

KitGuru noise guide
10dBA – Normal Breathing/Rustling Leaves
20-25dBA – Whisper
30dBA – High Quality Computer fan
40dBA – A Bubbling Brook, or a Refridgerator
50dBA – Normal Conversation
60dBA – Laughter
70dBA – Vacuum Cleaner or Hairdryer
80dBA – City Traffic or a Garbage Disposal
90dBA – Motorcycle or Lawnmower
100dBA – MP3 Player at maximum output
110dBA – Orchestra
120dBA – Front row rock concert/Jet Engine
130dBA – Threshold of Pain
140dBA – Military Jet takeoff/Gunshot (close range)
160dBA – Instant Perforation of eardrum

Noise (dBA)
152W	28.9
270W	29.9
400W	31.6
523W	34.2
652W	38.7

This isn't the quietest power supply we have tested, but it only really becomes audible in the top 20 percent of load. At realistic load figures between 40 and 70 percent it remains reasonably quiet.

Temperature (c)
	Intake	Exhaust
152W	35	37
270W	35	38
400W	38	44
523W	42	49
652W	45	53

The large Yate Loon 140mm fan helps to generate a high level of airflow across the components inside the chassis, with only an 8c above ambient intake registered.

Maximum load	Efficiency
715.8W	80.4

Pushing the PSU above its rated limits generates an efficiency level of around 80.4%. This is not a viable ‘real world’ situation, but its interesting nonetheless.

Become a Patron!